Cables · VOD Cable Blast Detection Cable
VOD Cable Blast Detection Cable: Material Library, Lot-Traceable.
VOD Cable Blast Detection Cable programs built on the Cavite floor — UFLPA-clean Philippine origin that is not subject to the China-specific Section 301 tariffs, IPC/WHMA-A-620 Class 3 acceptance by default. Send the drawing or part number and we will reply with unit price, lead time, and a sample plan inside 12 hours.
Buyer Reality
Where Most vod cable blast detection cable Programs Slip.
Issue #01
VOD trigger missed at primer initiation under 50 microseconds
VOD measurement requires sub-microsecond trigger latency; cable propagation drift over 5 ns/m masks the actual detonation velocity. Our VOD coax holds velocity-of-propagation per ISEE Field Practice within ±2% per reel.
Issue #02
Detonation-front shock-wave shears connector pins at 8 km/s
VOD primary detonation drives 8 km/s shock fronts that strip standard pin-and-socket connectors. We use sacrificial single-shot screw terminations rated per ISEE Blasters' Handbook §11.
Issue #03
Coaxial shield short to ground from shrapnel impact
Coax shield shorts to ground after first blast cycle if drain-wire termination is exposed. Our VOD-cable termination potting uses Sika-Force 7710 polyurethane qualified per MIL-STD-810H method 522.2 ballistic-shock.
Issue #04
Cable-line damage masks the trigger event
Damaged trigger line opens before the VOD probe registers; lost data on a single-shot test. Our QC ships paired backup trigger lines with each VOD harness with continuity-tested handover documentation.
Issue #05
Single-shot calibration drift from previous test residue
Re-using VOD probe holders without thorough cleaning embeds primer residue that biases the next velocity reading. Our build kit ships single-shot disposable probe holders sealed in sterile pouches per ISEE Test Method §2.6.
What We Build
The Capability Stack Behind The Build.
ISEE Blasters' Handbook §11 build practice
VOD probe and trigger-line build to ISEE Blasters' Handbook §11 (electronic blasting). Probe spacing ±1 mm, trigger line continuity verified at handover, sacrificial termination protocol on every kit.
Traceable VOD probe termination stock
VOD probe sacrificial terminations stocked on-site with full lot traceability. Single-shot rated per IEC 61496-3.
Coax velocity-of-propagation ±2% per reel
Tektronix DSA8300 sampling oscilloscope verifies VOD coax velocity-of-propagation per IEC 61169-58 — ±2% tolerance per reel. Calibration log archived for 10 years per ISEE traceability.
Sika polyurethane ballistic-shock potting
Sika-Force 7710 polyurethane potting at termination, MIL-STD-810H method 522.2 ballistic-shock qualified. Single-shot disposable probe holders shipped in sterile pouches.
Mining UL 2225 MC-HL cable library
UL 2225 Type MC-HL armored cable for hazardous-location mining, PVC / TPU / EPR jacket variants per MSHA 30 CFR §75.514 mine power. Single-shot detonation harnesses pre-qualified for ANFO / emulsion.
PEZA-signed certificate of origin on every commercial invoice — outside China Section 301
TPE strain-relief library qualified at IP67 / IP68
Flex-life validation by program per IEC 60068-2-31
FAQ
Procurement Questions, Answered.
Q.01What is the minimum order quantity for vod cable blast detection cable?
+
What is the minimum order quantity for vod cable blast detection cable?
Q.02What lead time do you commit to on vod cable blast detection cable after RFQ?
+
What lead time do you commit to on vod cable blast detection cable after RFQ?
Q.03Are vod cable blast detection cable shipments subject to the China Section 301 tariffs when imported into the US?
+
Are vod cable blast detection cable shipments subject to the China Section 301 tariffs when imported into the US?
Q.04Do you ship vod cable blast detection cable samples for free?
+
Do you ship vod cable blast detection cable samples for free?
Q.05Can you handle the vod cable blast detection cable engineering review before we have a finalized drawing?
+
Can you handle the vod cable blast detection cable engineering review before we have a finalized drawing?
Q.06Can samples ship before tooling? (Blast Detection)
+
Can samples ship before tooling? (Blast Detection)
Q.07How is ITAR or EAR handled? (Blast Detection)
+
How is ITAR or EAR handled? (Blast Detection)
Q.08How are common use issues reviewed? (Blast Detection)
+
How are common use issues reviewed? (Blast Detection)
Q.09Do you check manufacturability first? (Blast Detection)
+
Do you check manufacturability first? (Blast Detection)
Q.10What sample policy applies? (Blast Detection)
+
What sample policy applies? (Blast Detection)
Industries
Capabilities
Submit RFQ
Submit your VOD Cable Blast Detection Cable drawing.
Send the drawing, BOM, or part number plus annual volume. Engineering desk replies within 12 hours with unit price, lead time, sample plan, and a certificate-of-origin specimen documenting Philippine origin if you need import-classification support (standard US import duties may still apply, as determined by your customs broker). Standards reference:, IATF 16949 (https://en.wikipedia.org/wiki/ISO/TS_16949).
Reviewed by Hommer Zhao- Cavite-based wire harness engineer at XUDONG, IPC/WHMA-A-620 Class 3 trained, 8+ years in automotive & medical harness manufacturing.
Next Step
Ready For Your Vod Cable Blast Detection Cable Quote?
Send the drawing, BOM, or part number. We reply within 12 hours with unit price, lead time, and a sample plan. Quote returned within 12 hours. NDA on file. No obligation.