Cables · Edp Cable
Edp Cable: Material Library, Lot-Traceable.
Edp Cable programs built on the Cavite floor — UFLPA-clean Philippine origin that is not subject to the China-specific Section 301 tariffs, IPC/WHMA-A-620 Class 3 acceptance by default. Send the drawing or part number and we will reply with unit price, lead time, and a sample plan inside 12 hours.
Buyer Reality
Where Most edp cable Programs Slip.
Issue #01
eDP HBR3 8.1 Gbps insertion loss exceeds VESA 1.4b -8 dB budget
Aux-pair skew over 30 ps and intra-pair skew over 10 ps fails VESA eDP 1.4b link training at HBR3. We sweep S-parameters on a Keysight ENA-X up to 14 GHz and bin assemblies that exceed the VESA insertion-loss mask.
Issue #02
40-pin LVDS connector backshell ground-paddle floats
I-PEX CABLINE-CA II 40-pin assemblies short to chassis when the ground paddle is hand-soldered with paste mass over 0.4 mg. Our hot-bar reflow holds paste mass to ±0.05 mg per joint per JEDEC J-STD-001 §5.2.
Issue #03
Micro-coax 40 AWG drain-wire breaks at coverlay edge
40 AWG silver-plated copper drain wires fatigue at the coverlay step transition under repeated lid open/close. Our drain-wire qualification runs IEC 61169-58 §9.3 to 50,000 hinge cycles per program.
Issue #04
eDP panel-side connector pitch crush at 0.5 mm
0.5 mm-pitch I-PEX 20454 receptacles get crushed when the operator uses a 0.4 mm-fixture micro-coax. Our cell holds connector-specific torque jigs and barcoded pitch verification before mate.
Issue #05
HBR3 link training fails at -25C cold start
PI dielectric loss tangent rises 18% at -25C; an eDP cable that passes 23C training fails AEB ECR.011 cold-start link training. We thermal-cycle assemblies per IEC 60068-2-14 method Nb (-25 to +85 C) and re-verify HBR3 lock at each plateau.
What We Build
The Capability Stack Behind The Build.
VESA eDP 1.4b S-parameter sweep
Keysight ENA-X 14 GHz vector network analyzer sweeps insertion loss, return loss, NEXT/FEXT against the VESA eDP 1.4b mask on every cable build. S-parameter file (.s4p) attached to harness barcode.
I-PEX / JAE / Molex micro-coax stock
I-PEX CABLINE-CA II, JAE WP3, Molex Pico-EZmate sourced through traceable channels with quarterly lot inspection per IEC 61169-58. contact-finish record on every reel.
Hot-bar reflow per IPC J-STD-001 Class 3
Unitek hot-bar reflow stations hold paste mass tolerance ±0.05 mg per joint, peak temperature ±3 C against profile. Class 3 acceptance per IPC J-STD-001 §5.2.2 — every joint.
40 AWG micro-coax cross-section per build
40 AWG silver-plated copper micro-coax cross-section under Olympus BX53 metallograph against the customer drawing. Strand count, dielectric concentricity, drain-wire pickup verified per IPC/WHMA-A-620 §6.3.
Cold-start link verification IEC 60068-2-14
On-site Espec PL-3KP thermal chamber runs -40 C to +125 C cycles. eDP HBR3 link training re-verified at each thermal plateau before sample release.
Cirris CR/CH 100% continuity and 1500 V HiPot
Philippine origin outside the China-specific Section 301 tariffs
Komax + Schleuniger crimp cells with 100% CFM
FAQ
Procurement Questions, Answered.
Q.01What is the minimum order quantity for edp cable?
+
What is the minimum order quantity for edp cable?
Q.02What lead time do you commit to on edp cable after RFQ?
+
What lead time do you commit to on edp cable after RFQ?
Q.03Are edp cable shipments subject to the China Section 301 tariffs when imported into the US?
+
Are edp cable shipments subject to the China Section 301 tariffs when imported into the US?
Q.04Do you ship edp cable samples for free?
+
Do you ship edp cable samples for free?
Q.05Can you handle the edp cable engineering review before we have a finalized drawing?
+
Can you handle the edp cable engineering review before we have a finalized drawing?
Q.06Do you offer paid prototype builds? (Edp)
+
Do you offer paid prototype builds? (Edp)
Q.07How do you protect customer IP? (Edp)
+
How do you protect customer IP? (Edp)
Q.08Which certifications ship with lots? (Edp)
+
Which certifications ship with lots? (Edp)
Q.09What payment terms are typical? (Edp)
+
What payment terms are typical? (Edp)
Q.10How fast is DFM feedback? (Edp)
+
How fast is DFM feedback? (Edp)
Submit RFQ
Submit your Edp Cable drawing.
Send the drawing, BOM, or part number plus annual volume. Engineering desk replies within 12 hours with unit price, lead time, sample plan, and a certificate-of-origin specimen documenting Philippine origin if you need import-classification support (standard US import duties may still apply, as determined by your customs broker). Standards reference:, IPC standards (https://en.wikipedia.org/wiki/IPC_%28electronics%29).
Reviewed by Hommer Zhao- Cavite-based wire harness engineer at XUDONG, IPC/WHMA-A-620 Class 3 trained, 8+ years in automotive & medical harness manufacturing.
Next Step
Ready For Your Edp Cable Quote?
Send the drawing, BOM, or part number. We reply within 12 hours with unit price, lead time, and a sample plan. Quote returned within 12 hours. NDA on file. No obligation.