Israel · Automotive · EV / High-Voltage · Cavite Manufacturing
Israel Automotive & EV Wire Harness
Automotive and EV wire harness manufacturing in Cavite, Philippines — including EV high-voltage harnesses — with IATF 16949 process discipline, PPAP, and a non-China production origin. Built for Israeli electronics, medical, aerospace, and industrial OEMs that need a reliable overseas, non-China manufacturing partner for supply-chain resilience.
Immediate Proof
PH
Country of origin
Cavite Economic Zone
IATF
16949 certified
APQP / PPAP QMS
1 pc
NPI MOQ
Samples on production cells
12 h
RFQ response
Engineering desk, M-F
Automotive & EV
Automotive Harnesses, EV High-Voltage Included.
Automotive and EV harness programs carry process expectations that go beyond a clean crimp: IATF 16949 discipline, APQP planning, PPAP submission, FMEA, control plans, and MSA. The Cavite floor runs harness programs against that framework, with IPC/WHMA-A-620 Class 3 acceptance as the workmanship baseline.
EV brings the additional demands of high-voltage harnesses: orange high-voltage cable (typical EV battery and drive-system voltages, commonly into the hundreds of volts DC), shielded and HV-interlock-loop (HVIL) circuits, larger conductors and ring/lug terminals (heavy-gauge battery and bus leads down through signal conductors), HiPot and insulation-resistance testing, and routing discipline for safety and EMI. These are built and tested as a controlled process with documented evidence; HV dielectric and insulation-resistance test parameters are agreed against your specification, and certified safety-agency or homologation testing, where required, is routed to a customer-approved lab rather than claimed in-house. Our scope is harness build and electrical test — we do not perform vehicle-level validation or issue safety-agency certifications ourselves.
Whether the program is a low-volume validation build or a production automotive harness, NPI starts at one piece on the intended production cell, and the first 12-hour RFQ reply states the PPAP path, lead time, and connector strategy.
PPAP-Ready From The Start
APQP, PPAP, FMEA, control plans, and MSA structured for automotive and EV programs, so the documentation is built alongside the harness, not bolted on later.
English-Speaking Engineering Desk
Israeli engineering teams work directly in English with the Cavite desk — work instructions, RFQ replies, DFM notes, and audit calls are handled in English without an extra relay layer.
Practical Lead Time To Israel
Cavite ships to Israel by air or sea freight through standard forwarders. The Asia-to-Israel timezone overlap gives same-working-day engineering review on most RFQs, and lead times are quoted realistically in the first reply.
Comparison
Generic Harness Shop vs XUDONG Cavite (Automotive/EV)
Automotive and EV buyers need a harness manufacturer that speaks PPAP and high-voltage safety, not just crimp counts. This comparison reflects that decision.
| Decision Factor | Typical local / China sourcing | XUDONG · Cavite |
|---|---|---|
| Process discipline | ISO claim may not map to IATF 16949 APQP / PPAP expectations. | IATF 16949 discipline with APQP, PPAP, FMEA, control plans, and MSA. |
| EV high-voltage | High-voltage harness experience and HiPot evidence may be limited. | Orange HV cable, shielded / interlock circuits, HiPot and insulation-resistance testing with records. |
| Acceptance baseline | Class 2 unless Class 3 is called out and priced. | IPC/WHMA-A-620 Class 3 acceptance as the default workmanship baseline. |
| Validation & low volume | Validation builds pushed to higher MOQs. | 1-piece NPI for validation builds, with pilot and production tiers and a stated PPAP path. |
| Origin & resilience for Israeli buyers | Single-source China exposure or capacity-limited local suppliers can leave a program without a documented second source. | Non-China Philippine origin with PEZA export records gives Israeli procurement a defensible dual-source / BCP option with a clear audit trail. |
Program Process
How A Program Starts
The fastest way to qualify an overseas supplier is to make the first week concrete: drawing review, engineering questions, sample plan, quality documentation, and export assumptions. That is how we structure the kickoff.
01
Send drawings, BOM, photos, or a sample
DXF, PDF, harness-board photos, connector list, annual volume, target lead time, and required documentation are enough for the first review. A mutual NDA can be signed before drawing transfer.
02
Free DFM and material review
Cavite engineering checks connector availability, crimp tooling, fixture-board need, cable jacket, test requirements, and any overmold or backshell tooling. The first reply includes NPI, pilot, and production pricing.
03
Sample on the production cell
The first article is built on the intended Cavite production cell. Cross-section photos, pull-force logs, continuity, HiPot, and dimensional checks ship with the sample.
04
Pilot lot and control-plan lock
Pilot production validates operator cycle time, fixture repeatability, connector supply, packing method, and inspection sampling. The control plan is locked only after pilot defects and customer comments are closed.
05
Production plus export package
Commercial shipments include the PEZA export record, certificate-of-origin support, invoice, packing list, and traceability records your customs broker or freight forwarder needs.
Capability Stack
Automotive & EV Harness Capability
Automotive and EV harness programs built to IATF 16949 process discipline, including EV high-voltage harnesses, with the documentation automotive customers expect.
Automotive harnesses
Branched body, chassis, and module harnesses with fixture-board production and per-leg labeling.
EV high-voltage harnesses
Orange HV cable, shielded and HV-interlock-loop (HVIL) circuits, large-conductor ring/lug terminals, and HV-safe routing for typical EV battery and drive-system voltages (commonly up to several hundred volts DC), with HiPot and insulation-resistance parameters set to your specification. Certified safety-agency / homologation testing, where a program requires it, is routed to a customer-approved lab.
Sealed & waterproof
Sealed connectors, grommets, and IP-rated exits for under-hood and exterior applications.
PPAP / APQP package
APQP planning, PPAP submission, FMEA, control plans, and MSA records for automotive programs.
HV & electrical test
HiPot, insulation resistance, continuity, crimp cross-section, and pull-force verification.
Connector & terminal library
Brand-authorized automotive connector and terminal sourcing with calibrated applicators.
Facility
Built In Cavite, Not Re-Labeled In Cavite.
XUDONG's Cavite operation in the Philippines handles wire harness assembly, cable assembly, box build, test, inspection, packing, and export processing inside the Cavite Economic Zone. Programs are not transshipped — the production record, operator record, inspection record, and export record all point to the same plant.
For overseas buyers that matters more than a brochure: when a customer auditor or internal compliance team asks where the work is performed, the answer is a program file showing the production cell, the materials that entered the line, the operators who ran the cell, and the export documents that accompanied the shipment.
Certifications & Records
Audit Pack Before Production.
The certificate list is only the front page. For active programs, the real audit pack includes control plans, calibration records, operator training, material declarations, inspection logs, and origin-support documentation tied to the shipment.
CERT.01
IATF 16949
Automotive-grade process control with APQP / PPAP discipline and structured corrective action.
CERT.02
ISO 9001:2015
Documented quality management system with annual audit discipline.
CERT.03
ISO 13485
Medical-device quality documentation path for regulated electronics and cable assemblies.
CERT.04
IPC/WHMA-A-620
Class 3 cable and wire harness acceptance as the default inspection baseline; operators trained to the standard.
CERT.05
RoHS / REACH
BOM-line material compliance declarations available for customer audit packs.
CERT.06
PEZA Export Records
Cavite Economic Zone export documentation used in the origin and customs-support package.
Related Pages
Keep The Search Intent Connected.
Wire Harness
Full harness capability by build type, standard, and industry.
Automotive & EV
Automotive and EV harness programs, standards, and validation context.
Cable Assembly
Coax, power, and shielded cable assemblies for automotive and EV builds.
China+1 Sourcing
Non-China origin for automotive supply-chain diversification and BCP.
FAQ
Procurement Questions, Answered.
Q.01Do you build EV high-voltage wire harnesses?
+
Do you build EV high-voltage wire harnesses?
Q.02Can you provide PPAP for automotive programs?
+
Can you provide PPAP for automotive programs?
Q.03Do you support Israeli OEMs in English?
+
Do you support Israeli OEMs in English?
Q.04Can you ship to Israel and document non-China origin?
+
Can you ship to Israel and document non-China origin?
Submit RFQ
Send The Automotive Or EV Harness Drawing.
Attach the harness drawing, connector and terminal list, BOM, PPAP requirement, and annual volume. We reply within 12 working hours with price tiers, sample timing, the PPAP path, and the documentation plan.
Next Step
Send The Automotive Or EV Harness Drawing.
Send the drawing, BOM, or current supplier package. Quote returned within 12 hours. NDA on file. No obligation.